Drywall Takeoff Services for Installation and Repair Estimates

Two drywall bids can carry the same square footage and still be thousands of dollars apart. The difference is usually finish level, board type, or wall height, not the board count. A Level 5 finish adds a skim coat over the entire surface. A Level 4 finish only coats the joints and fasteners. 247 Estimation prices every wall type, ceiling assembly, and finish level as its own line, whether you need an estimate for drywall installation or an estimate for drywall repair.

Why Drywall Estimating Is More Than Square Footage

Drywall is bought by the sheet but priced by the assembly. A partition may carry one layer of 1/2-inch board or two layers of 5/8-inch Type X on each side. It may sit on 25-gauge studs or 20-gauge studs with a deflection track. Each change moves material, labor, and finishing time.

Labor is the largest part of the price. BLS reports a 2024 median wage of $58,800 for drywall installers, ceiling tile installers, and tapers. Tapers earn more than hangers, so finish level has an outsized effect on labor cost. Our drywall estimating services price hanging and finishing as separate lines for that reason.  

What Our Drywall Takeoff Services Measure

Gypsum Board:

Regular, Type X, Type C, moisture-resistant, abuse-resistant, and shaftliner board, counted by thickness, sheet size, and layer for every wall and ceiling type.

Metal Stud Framing:

Studs and track by size, gauge, and spacing, plus deflection track, headers, kickers, backing, and blocking, counted by wall type and partition height.

Ceilings and Soffits:

Drywall ceilings, suspended drywall grid, bulkheads, and soffits, measured by square foot and linear foot, with hanger wire and framing listed separately.

Taping and Finishing:

Joint tape, joint compound, corner bead, and trim, priced by finish level from Level 0 to Level 5, with skim-coat areas marked on the plans.

Insulation and Sound Control:

Batt, mineral wool, and sound attenuation blankets by thickness and R-value, plus resilient channel and acoustic sealant at rated walls.

Fire-Rated Assemblies:

Rated walls, shaft walls, and floor-ceiling assemblies matched to their tested UL design, with layer counts and board type checked against the drawings.

Firestopping:

Head-of-wall joints and penetration seals at rated walls, counted by location and system, so firestopping never falls between the drywall and MEP scopes.

Exterior Sheathing:

Glass-mat gypsum sheathing and exterior soffit board by square foot, with fasteners, joint treatment, and weather barrier accessories listed separately.

Board Types and Coverage

Board Type Common Thickness Typical Use Sheet Sizes
Regular gypsum board 1/2" Non-rated walls and ceilings 4x8, 4x10, 4x12
Type X 5/8" Fire-rated walls and garage separations 4x8, 4x10, 4x12
Type C 5/8" Fire-rated floor-ceiling assemblies 4x8, 4x10, 4x12
Moisture-resistant 1/2" or 5/8" Bathrooms and humid areas, not wet zones 4x8, 4x12
Abuse- or impact-resistant 5/8" Corridors, schools, healthcare 4x8, 4x10, 4x12
Shaftliner 1" Elevator and mechanical shaft walls 2x8 to 2x12
Glass-mat sheathing 1/2" or 5/8" Exterior wall sheathing 4x8, 4x9, 4x10

A 4x8 sheet covers 32 SF, and a 4x12 sheet covers 48 SF. Larger sheets mean fewer joints and less finishing labor on tall walls. Waste typically runs 5% to 10%. Small rooms, many openings, and cut-up layouts push it higher.

Finish Levels and What They Do to the Price

The Gypsum Association’s GA-214 defines six levels of finish, from Level 0 (no taping or finishing) to Level 5. Level 4 is the most common finish under flat paint. GA-214 calls for Level 5, a skim coat over the entire surface, under gloss or semi-gloss paint and where lighting is critical.

Level What It Includes Typical Location Labor Impact
Level 0 No tape or finishing Temporary walls None
Level 1 Tape embedded in compound Above ceilings, plenums Lowest
Level 2 Tape plus one coat over joints and fasteners Garages, behind tile Low
Level 3 Two coats over joints, ready for heavy texture Textured walls Moderate
Level 4 Three coats over joints, sanded smooth Flat-paint rooms Standard
Level 5 Level 4 plus a full skim coat Gloss paint, critical lighting Highest

Finish level is often shown only in the spec, not on the plans. Our takeoffs map each finish level by room so the labor line matches the actual scope.

Commercial Drywall Estimating

Commercial drywall estimating runs on wall types. Each partition tag on the plan points to a wall type schedule that sets board layers, stud size, gauge, insulation, and fire rating. Our commercial drywall estimating services trace every partition to its wall type and height before counting a single sheet.

Commercial scopes also carry items residential work skips:

Each item is listed by floor and area, so the GC can split the drywall number by phase or building.

Interior Drywall Takeoff Services

Our interior drywall takeoff services cover tenant improvements, multifamily units, hotels, schools, and healthcare interiors. Each room is measured by wall height, ceiling type, and finish level. Unit-type matrices let multifamily and hotel takeoffs repeat across floors without recounting.

Wall height matters as much as length. Walls over 10 feet need longer sheets, scaffolding or lifts, and heavier studs. Our takeoffs flag every tall wall so the labor line carries the right production rate.

Estimate for Drywall Installation

An estimate for drywall installation starts with net wall and ceiling area after openings. Board is converted to sheets by size and layer. Framing, finishing, insulation, and accessories are added by assembly. Labor is priced by hanging rate and finishing rate.

Installed costs vary widely by scope. Cost guides put typical drywall installation at about $1.50 to $3.50 per square foot. Many homeowners pay $2 to $2.50 per square foot for hang and finish at Level 4. Commercial work with rated walls and metal framing runs higher. Every drywall installation estimate we prepare is priced at the project’s own ZIP code.

Estimate Drywall Repair and Restoration Work

To estimate drywall repair, the scope comes first, then the price. A small hole, a water-damaged ceiling, and a fire-damaged wall each follow different rules. Our drywall repair estimates are built for restoration contractors, property managers, insurance adjusters, and homeowners who need a line-item number.

Water Damage Category Sets the Scope

The IICRC S500 standard groups water damage into three categories. Category 1 is clean water. Category 2 is gray water. Category 3 is grossly contaminated water, such as sewage or floodwater. Porous materials like drywall hit by Category 3 water are generally removed, not dried. Removal is often done as a flood cut 2 or 4 feet above the floor. Each cut height changes board, finishing, and disposal quantities.

Typical Drywall Repair Costs

Repair Scope How It Is Measured Typical 2026 Range
Small hole (up to 6 in) Per patch $50 to $150
Medium hole (6 to 12 in) Per patch $120 to $400
Larger patch or section Per SF $2.50 to $9.00 per SF
Texture and paint match Per room $150 to $900
Flood cut and replace Per LF of wall Priced by cut height and finish level

These ranges come from 2026 cost guides and change by region, texture, and access. Hourly repair rates commonly run $45 to $85 per hour.

Every estimate for drywall repair lists removal, disposal, new board, finishing, texture, and primer as separate lines. Insurance-ready line items can be formatted to match the carrier’s estimating program.

Regional Drywall Estimating

Labor rates, building types, and climate change the drywall number by state. Every job is priced at the project’s ZIP code using RSMeans and current supplier quotes.

Florida:

Our Florida drywall takeoff services account for humidity and storm damage. Moisture- and mold-resistant board is common in bathrooms, garages, and coastal buildings. Hurricane and flood repairs drive steady demand for water-damage drywall work. Drywall takeoff services in Florida tie into the Florida estimating team’s local rate data.

Georgia:

Our Georgia drywall takeoff services cover Atlanta’s multifamily, hotel, and data center interiors. Data centers carry heavy rated-wall and shaft wall scopes. Drywall takeoff services in Georgia use the Georgia estimating team’s labor and material rates.

Texas:

Drywall takeoff services in Texas cover large multifamily and tenant improvement work across Dallas, Houston, Austin, and San Antonio. Gulf Coast storm repairs add water-damage scopes. The Texas estimating team supplies local rates.

Our drywall estimating services in USA cover all 50 states, for residential, commercial, and restoration work.

Who Uses Our Drywall Estimating Services

Drywall Takeoff Software and CSI Placement

Our estimators work in PlanSwift, Bluebeam Revu, and On-Screen Takeoff. Each wall type and ceiling assembly gets its own color layer on the plans. Quantities export to Excel by CSI section.

  • 07 21 00: Thermal insulation
  • 07 84 00: Firestopping
  • 09 21 16: Gypsum board assemblies
  • 09 22 16: Non-structural metal framing
  • 09 29 00: Gypsum board
  • 09 51 00: Acoustical ceilings

We accept PDF plan sets, DWG files, and Revit models.

Why Contractors Choose 247 Estimation

Wall-Type Detail

Every partition is traced to its wall type, height, and rating. Board layers and stud gauge come from the schedule, not an assumption.

Finish Levels Mapped

Each room carries its finish level on the takeoff. Level 5 areas are flagged so the labor line is never short.

Color-Coded Markups

Wall types, ceilings, and rated assemblies each carry their own color. Any number traces back to the plans.

Free Addenda Updates

Revised partition plans or wall schedules that arrive mid-bid are added at no extra charge.

How 247 Estimation Builds a Drywall Estimate

Drawing and Spec Review

The team reads floor plans, reflected ceiling plans, wall type schedules, and the Division 09 specs. Fire ratings and finish levels are confirmed first.

Wall and Ceiling Measurement

Each wall type is measured by length and height. Ceilings are measured by area and type. Openings are deducted.

Material Conversion

Area converts to sheets by size and layer. Studs, track, tape, compound, bead, and fasteners are counted by assembly.

Labor and ZIP-Code Pricing

Hanging and finishing labor are priced separately by production rate. Material and labor rates are set at the project ZIP code.

Quality Review

A senior estimator checks the takeoff against the plans and past jobs of similar size. Delivery is typically 2 to 4 business days. Each package ships with marked-up plans and a line-item spreadsheet.

You can review our estimation examples to see the format before ordering.

Common Drywall Bid Errors and How We Catch Them

Error What Goes Wrong Pre-Bid Check
Single board type Rated and non-rated walls priced the same Board type set by wall type schedule
Missing layers Double-layer rated walls counted as one layer Layer count from the UL design
One finish level Level 5 areas priced at Level 4 Finish level mapped by room
Flat wall height Tall walls priced at 8-foot production rates Wall heights checked on sections
No deflection track Head-of-wall under decks left out Head details checked per wall type
Firestopping skipped Penetrations left between trades Rated wall penetrations counted

Get a Drywall Estimate Built on Real Wall Types

A drywall bid holds up when board, framing, finishing, and labor each carry their own priced line. Upload your plans or repair photos on the contact page. The team will confirm scope and turnaround before work begins.

FAQs